DESCRIPTION
Specification:
Item Name: 115mm F4 OSD 1-2S 3 Inch Toothpick FPV Racing Drone;
Wheelbase: 115mm;
Size: 97x97x35mm (without propellers);
Optional Receiver Version:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode);
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter);
Internal SPI DSM2/DSMX version(Compatible with Spektrum or Multiprotocol DSM2/X radio);
Weight: 41g (without battery);
Recommend Lipo Battery: 2s 350mah/400mah/450mah/520mah Battery ( NOT Included).
EX1202.5 6400KV Motor -
Configu-ration: 9N12P;
Stator Diamter: 12mm;
Stator Length: 2.5mm;
Shaft Diameter: Φ1.5mm;
Motor Dimension(Dia.*Len): Φ14*14.5mm;
Weight: 4.4g;
No.of Cells(Lipo): 1-2S.
Gemfan 3018 2-Blade Propeller -
Center Thickness: 5.5mm;
Prop Diameter: 76.5mm;
Center Hole diameter: 1.5mm.
CrazybeeX FR V2.2 F4 Flight Controller -
MCU: STM32F411CEU6 (100MHZ, 512K FLASH);
Sensor: MPU6000 or ICM20689 or BMI270 (SPI connection);
Board Size: 28.5x28.5mm;
Power Supply: 1-2S battery input (DC 2.9V-8.7V);
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready;
Built-in Betaflight OSD(SPI Control);
Built-in 5.8G VTX;
Built-in SPI Frsky/Flysky receiver or no receiver;
Built-in 5V 1A BEC;
(Frsky SPI RX Version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR;
(Flysky SPI RX Version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS;
(DSM2/X SPI RX Version)CRAZYBEEX DXS V1.0 FC firmware target: CrazybeeF4DXS;
(External Frsky RXSR Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX;
(External TBS CRSF NANO Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX.
Onboard 5A BL_S 4in1 ESC -
MCU upgraded to EFM8BB21;
Power supply: 1S LiPo/LiPo HV;
Current: 5A continuous peak 6A (3 seconds);
Support BLHeliSuite programmable;
Factory firmware: S_H_50_REV16_7.HEX;
Default protocol: DSHOT600.
Onboard Frsky SPI D8 Receiver Version -
SPI BUS receiver Frsky D8 compatible;
Compatible Non EU transmitter D8 model;
Channels: 8ch;
Failsafe support;
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m.
Onboard Flysky SPI receiver Version -
Protocol: AFHDS and AFHDS-2A Switchable;
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A);
No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m;
Failsafe support.
Onboard DSM2/X SPI receiver Version -
SPI BUS receiver DSM2/DSMX compatible;
Channels: Max 12ch;
Failsafe support;
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m;
RSSI enable (show on the goggles).
Onboard 5.8G 40CH 25/200mW VTX -
Output power: 25mw~200mw switchable;
Frequency: 40CH;
Input voltage: 3.3V 5.5V;
Current consumption: 300mA(type);
Frequency: 5.8GHz 5bands 40 channels;
With Race band;
Smartaudio ready.
Caddx ANT 1200TVL Camera -
Image Sensor: 1/3' CMOS Sensor;
Horizontal Resolution: 1200 TVL;
TV System: NTSC or PAL Switchable;
IMAGE: 4:3;
Synchronization: Internal;
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000;
S/N Ratio: >52dB (AGC OFF);
Video Output: CVBS;
Lens: 1.8mm;
Min. Illumination: 0.001Lux@F1.2;
Auto Gain Control: YES;
BLC: YES;
WDR: Global WDR;
DNR: 3D DNR;
Dimensions: 14*14mm(with bracket to 19*19mm);
Wide Power Input: DC 3.7-18V;
Work Temperature: -20℃~+60℃;
Weight: 2g (N.W.).
Features:
- 41gram 1-2s brushless Toothpick drone;
- New AIO 4in1 CrazybeeX flight controller;
- CADDX ANT 1200tvl Camera;
- New 1202.5 brushless motor;
- XT30 connector;
- Compatible with Insta360 Go Camera ( this camera is NOT Included, you can add it by yourself.).
Pacakge Included:
1x Crux3 Frame and Canopy;
1x Optional Receiver;
1x F4 Flight Controller AIO 5A ESC Board;
1x 5.8G 25-200mW VTX ( built-in Flight controller);
4x Happymodel EX1202.5 6400 KV Motor;
4x Gemfan 3018 Propeller CW;
4x Gemfan 3018 Propeller CCW;
1x Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera;
1x Screw Driver;
1x Propeller Disassemble Tool;
1x Happymodel Handbag.
