DESCRIPTION
Micro FPV Whoop Drone:
We're glad to launched our new Mobula7 drone, this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season.
The world first 5-IN-1 AIO flight controller with ExpressLRS 2.0 , OPENVTX(up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD coming out recently. This is amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX range by using this flight controller.
The new RS0802 motors comes with a new unibell design, use 1.5mm shaft and include PCB bottom plate, high efficiency and much more reliable.
New onboard OpenVTX , max power up to 400mw, provide RCE and PIT mode, it was very useful for race event.
Features:
- Flight controller built-in 2.4G ELRS V2.0 and Openvtx;
- VTX Power up to 400mw;
- ELRS V2.0 Support;
- NEW RS0802 20000KV motors;
- Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera;
- Smooth and powerful;
- Compatible for 1S Lipo/LIHV;
- Recommend 1S 450mah/550mah/650mah battery (Not included).
Specifications:
Item Name: 75mm Micro FPV whoop drone;
Wheelbase: 75mm;
Size: 99mm*99mm*40mm;
Weight: 24g.
Motor -
Mode: RS0802 KV20000;
Configu-ration: 9N12P;
Stator Diamter: 8mm;
Stator Length: 2mm;
Shaft Diameter: Φ1.5mm;
Motor Dimension(Dia.*Len): Φ10.5mm*13.5mm;
Weight(g): 2.0g;
No.of Cells(Lipo): 1S only.
Propellers -
Weight: 0.24g;
Material: PC;
Pitch: 1 inch;
Props Dia: 40mm;
Center Thickness: 5mm;
Center Hole Dia: 1.5mm.
Flight controller -
X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280;
X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR;
X12 Flysky V1.0 flight controller built-in SPI Flysky 2.4G receiver Target: CRAZYBEEF4FS;
X12 PNP V1.0 flight controller without onboard receiver Target: CRAZYBEEF4DX;
MCU:STM32F411CEU6 (100MHZ, 512K FLASH);
Sensor: MPU6000 or ICM20689 (SPI connection);
Mount hole size: 25.5mm*25.5mm;
Power supply: 1S battery input (DC 2.9V-4.35V);
Built-in 12A(each) Blheli_S 4in1 ESC;
Built-in Betaflight OSD (SPI Control);
Built-in 5.8G OpenVTX 0mw~400mw;
Built-in ExpressLRS 2.4G, Frsky D8/D16, Flysky AFHDS 2A;
Built-in voltage detection;
Built-in current sensor.
Onboard 4in1 ESC -
Power supply: 1S LiPo/LiPo HV;
Current: 12A continuous peak 15A (3 seconds);
Support BLHeliSuite programmable;
Factory firmware: Z_H_30_REV16_7.HEX;
Default protocol: DSHOT300;
Support Bluejay firmware.
Onboard SPI ExpressLRS 2.4GHz Receiver ( 2.4G ELRS Receiver Version) -
Packet Rate option: 50Hz/150Hz/250Hz/500Hz;
ExpressLRS Firmware version: V2.0;
RF Frequency: 2.4GHz;
Antenna: SMD antenna;
Telemetry output Power: <12dBm;
Receiver protocol: SPI ExpressLRS;
Compatible with ExpressLRS V2.0 TX Module;
Couldn't flash separately ExpressLRS firmware.
Onboard Frsky SPI D8/D16 receiver compatible ( Compatible Frsky Receiver Version) -
SPI BUS receiver Frsky D8 compatible;
Compatible Non-EU transmitter D8 model;
Channels: 8ch;
No ground interference ( Transmitter and receiver 1 m from the ground): 200meter;
Failsafe support.
Onboard Flysky SPI receiver compatible ( Compatible Flysky Receiver Version) -
SPI BUS receiver;
Protocol: AFHDS and AFHDS-2A Switchable;
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A);
No ground interference ( Transmitter and receiver 1 m from the ground): 200meter;
Failsafe support.
PNP Version (without onboard receiver) -
Full UART1 for external Receiver;
Support CRSF/GHOST/SBUS/IBUS/DSMX protocol;
IR1 pad(invert RX1) used for SBUS input.
Onboard 5.8g OPENVTX -
Firmware version: OPENVTX;
Smart audio v2.1;
PIT Mode support;
RCE Mode support;
Channels: 48ch;
Transmitting Power: 0/RCE/25mw/100mw/400mw;
Power supply: DC 5V;
Current (5v): <650ma (400mw).
Runcam Nano3 -
Model: RunCam Nano 3;
Image Sensor: 1/3' CMOS;
Horizontal Resolution: 800TVL;
Lens : 2.1mm(M8) FOV 150°;
Signal System: NTSC;
S/N Ratio: >50dB;
Electronic Shutter Speed: Auto;
Auto Gain Control (AGC): Auto;
Min. Illumination: 0.01Lux@1.2F;
D-WDR: Auto;
Day/Night: Color;
Power:DC 3-5.5V;
Current: 110mA@5V 120mA@3.3V;
Housing Material: ABS;
Net Weight: 1.2g;
Dimensions: L14mm*W14mm*H9mm.
Recommend 1S Lipo Battery (Not included) -
Capacity: 650mAh;
Voltage: 3.8v;
Continuous Discharge Rate: 30C;
Instantaneous discharge rate: 60C;
Size: 60mmx18mmx8mm;
Weight: 16g;
Connector: PH2.0.
Package Included:
1x 75mm whoop Drone Frame (Mobula7 v4 frame).
1x Option1: X12 ELRS V1.0 flight controller built-in SPI ELRS 2.4G receiver.
1x Option2: X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver.
1x Option3: X12 Flysky V1.0 flight controller built-in SPI Flysky 2.4G receiver.
1x Option4: X12 PNP V1.0 flight controller without onboard receiver.
4x RS0802 KV20000 brushless motor.
1x Gemfan 1610-2 bi-blade propellers(4cw+4ccw).
1x Runcam Nano3 1/3 CMOS 800TVL camera.
1x Onboard 5.8G Openvtx 0mw~400mw VTX.
1x 1S parallel charging board.
1x Propeller disassemble tool.
1x Extra camera canopy.
